MB Quart NA2-500.5 specifications.

  Car amplifiers Specs << MB Quart << MB Quart NA2-500.5

Specification | Reviews
MB Quart NA2-500.5



General characteristics MB Quart NA2-500.5
Maximum Power:
500 Watts
Low Frequency Response:
50-150 Hz
Number of Channels:
5
Frequency Response:
20-20000 Hz
Built In Crossovers:
Yes
Channel Separation:
Yes
Amplifier Class:
D
Fuse Rating:
40x1 A
MARINE GRADE PROTECTION:
YES  Amplifiers are ABYC & ASTM certified which defines that marine amplifiers must use conformal coated PC boards to resist corrosion from salt spray & moisture.
PRE-AMP CIRCUITRY:
Q-Stasis Pre Amplifier Stage The highly engineered Q-Stasis pre-amplifier stage reduces incoming noise from source units dramatically improving sound quality
INPUTS:
2 Pair, RCA (Front/Rear) | 1 Pair RCA (Subwoofer) Nickel-Plated  High temperature impact resistant with hex screw terminals that allow for secure connections and is erosion resistant
OPERATION MODE:
Four channel and with dedicated subwoofer channel  Unique design allows this amplifier to power full range speakers with a dedicated channel for a subwoofer.
CROSSOVER / SIGNAL SHAPING:
Switched FULL / LPF / HPF  Complete control of amplifier signal, essential when using two or more amplifiers
CLASS / TOPOLOGY:
Full Range Class D  Highly efficient circuit topology which helps the amplifer develop a lot of power in a very small heatsink.
OUTPUT DEVICES TECHNOLOGY:
PWM MOSFET Power Supply  Stable power through the PC board with minimal heat generation
HEAT SINK:
Aluminum  Quickly dissapates heat to allow the amplifer to run lower impedance for longer duration
POWER SUPPLY:
Simpatico Coil Design  The dual coil Pulse Width Modulated power supply keeps voltage constant through the Ultra-Fi output devices
Bass Remote:
Included  Wired Bass Remote allows adjustments to bass frequencies to be made from the control mounted anywhere in the vehicle.
OUTPUT CONNECTIONS:
Quick Dissconect Wires, RCA Connections  Quickly remove amplifer when you are putting machine up for the winter of as a security precaution
CONNECTIONS TYPE:
Nickel-plated connections  Nickel plated corrosion resistant connections
DIAGNOSTICS:
Three-stage protection circuits  Monitor thermal, overload, DC, and speaker short protection with lighted indicators on the amplifier end panel
MARINIZED / WATERPROOF:
YES  Water resistant for durability in any environment
Class:
Full Range Class D
Variable Voltage:
0.2V~9V
Signal to Noise Ratio:
>90dB
Frequency Response:
20Hz-20kHz
CROSSOVER TYPE:
N/A
CROSSOVER FREQUENCY RANGE:
CH1 & CH2 | Switched HP/ Full
CROSSOVER FREQUENCY RANGE:
CH3 & CH4 | Switched HP/ Full
CROSSOVER FREQUENCY RANGE:
CH5 | LPF 50Hz-150Hz
Bass Boost:
0-12dB@45Hz
Subsonic Filter:
60Hz
POWER @ 2-OHMS:
4 x 80W 1 x 200W
POWER @ 4-OHMS:
4 x 40W 1 x 100W
Total Channels:
5
Audio Inputs:
RCA
Power Terminal 12v/gnd:
Molex 10 ga
Speaker Terminal Wire Gauge:
Molex Plug Connector
Fusing:
1 x 40 Amps
CERTIFICATIONS:
Marine & Powersports
Dimensions:
3.70 X 8.46 X 1.77 in | 9.4 X 21.5 X 4.5 cm
Weight:
3.35 lbs (1.52 kg)
Weight:
10


Popular today


Autotek MM4020.4
Autotek MM4020.4
Maximum Power: 4000 Watts; Low Frequency Response: 30-250 Hz; High Frequency Response: 60-1200 Hz; Number of Channels: 4; Frequency Response: 15-150 Hz; Built In Crossovers: Yes; RMS Power Output: 100...
Autotek MM3020.1D
Autotek MM3020.1D
Maximum Power: 3000 Watts; Low Frequency Response: 40-300 Hz; Number of Channels: 1; Frequency Response: 15-150 Hz; Built In Crossovers: Yes; RMS Power Output: 1500x1 Watts; Channel Separation: No; Am...